Burnatonce error message...please help

[DD51]

I succesfully burned a DataCD yesterday...without any problems at all.

So I uninstalled Nero

Today I tried burnign another DATACD with this error message:



Cdrdao version 1.1.7 - (C) Andreas Mueller <andreas@daneb.de>
SCSI interface library - (C) Joerg Schilling
Paranoia DAE library - (C) Monty

Using libscg version 'andreas-0.5-UNIXWARE_Patch'

1,0,0: PIONEER DVD-RW DVR-105 Rev: 1.30
Using driver: Generic SCSI-3/MMC (raw writing) - Version 2.0 (options 0x0000)

Starting write at speed 8...
Turning BURN-Proof on
Using 16 byte P-Q sub-channel data mode.
Executing power calibration...
Power calibration successful.
Writing lead-in and gap...
?: I/O error. : scsi sendcmd: retryable error
CDB: 2A 00 FF FF D4 47 00 00 1B 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 02 00 00 00 00 0E 00 00 00 00 04 08
Sense Key: 0x2 Not Ready, Segment 0
Sense Code: 0x04 Qual 0x08 (logical unit not ready, long write in progress) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.007s timeout 20s
ERROR: Write data failed.
ERROR: Writing failed.

What did I do wrong???
Thanks

 

[scarecrow]

1. What were you trying to burn using the RAW driver?
2. Do you have Imapi or a packet writer active?
3. what OS are you using?

 

[zver]

Dont tell nothing bud--i formatting my hd(but this is also incompatibility with my pc)........Never buy a f.....n pacckard

 

[DD51]

Scarecrow thanks for responding...

1. What were you trying to burn using the RAW driver?
A datacd (MP3 music) I burned a cd yesterday no problem at all
Should I not be chosing Raw?


2. Do you have Imapi or a packet writer active?
Have no idea what that is!
I have aspi 4.6 installed
It's a Pioneer DVD A05 with the latest firmware 2X4all


3. What OS are you using?
XP Pro with all the updates installed

If you need more info please let me know...thanks again for your help.

 

[Duracell]

"2. Do you have Imapi or a packet writer active?"
Have no idea what that is!

it's for copying files via "Drag & Drop" to a CD-RW, using a CD-RW like a floppy disk without using a CDR mastering software;
examples for packet writers: InCD, FileCD, InstantWrite ...

and what scarecrow asked also above: Did you deactivated XP's native IMAPI burning engine? ==> Control Panel > Administration > Services > IMAPI > Start Type > disabled


Greetings from
Duracell

 

[scarecrow]

DD51,
No, you should not use the RAW driver for burning data CD's- the default one (SCSI3-MMC) is just fine. Actually BAO is quite "clever" to auto switch to the RAW driver when needed (eg burning audio CD's with CD-Text included).
Imapi can be found and disabled under Administration tools/services.
Your log file says that CDRDAO lost contact with the device right after burning the lead-in area because of "something"- which may have been Imapi, especially if you have auto insert notification turned on.
By the way you can post the same question to Burnatonce forums.

 

[DD51]

Duracell...Thank you soo much for your responce...it is greatly appreciated.

Scarecrow,
That's it...It works now! I must've put a check mark in the Raw Write box! I removed the check and all is fine now! Thank you soo much for helping me...What a great little program.

I appreciate everyone's help with this

PS I check my ATAPI and it was on Manual! I don't know if it's the reason why but I changed it to Automatic.

Sincere regards,

 

[scarecrow]

PS I check my ATAPI and it was on Manual! I don't know if it's the reason why but I changed it to Automatic.

You obviously mean "Imapi". Believe me, setti9ng it to "disabled" instead makes much more sense, since this service is almost useless (a very limited packet writer). If you decide to do so, do it under the "extended" services tab.
By the way Burnatonce is one of my darlings, too.

 

[DD51]

Scarecrow,

Once again thank you soo much for the tips!!!
and yes i did mean IMAPI.

I am overwhelmed by the help here...you guys are too much!

Thanks again...I have disabled it under the extended tab

Regards,