NERO 6.0.0.9 for max.7 recorders ??? HELP
- Thread starter Pedja
- Start date
OK, Nero will give you just SIX coasters then...
Use either Discjuggler or RecordNowMax which are tailor made for burning to multiple recorders, nobody in a "mildly serious" state of mind uses Nero for mass duplication.
You must not have two recorders on the same IDE channel, else coasters are 99.9% guaranteed.
Use either Discjuggler or RecordNowMax which are tailor made for burning to multiple recorders, nobody in a "mildly serious" state of mind uses Nero for mass duplication.
You must not have two recorders on the same IDE channel, else coasters are 99.9% guaranteed.
Master
Gold Member
You have to buy a lisence from ahead to burn with 7 recorders at one time.
I didn´t say that this will work without problems but a stable system with 2 scsi controller and 6 equal scsi writer will do it.
Perhaps you can try a naked system with 2 extra promise ide controller too.
I didn´t say that this will work without problems but a stable system with 2 scsi controller and 6 equal scsi writer will do it.
Perhaps you can try a naked system with 2 extra promise ide controller too.
Last edited:
Master
Gold Member
I never tried this so i am not sure that i am right.
i would buy a big tower with a big psu ..500watt or more.
A mobo with a normal ide controller plus an extra onboard raid/udma133 solution....onboard sound and lan would be fine too.
Then i would buy two extra promise pci ide controller cards.
I would use the normal ide controller for a big hd and a dvd-rom drive.
On every channel of the promise controller and onboard raid controller i would use one writer only.
I am not sure if this will work..perhaps you will get some probs with the irq´s or the busmaster signal.
i would buy a big tower with a big psu ..500watt or more.
A mobo with a normal ide controller plus an extra onboard raid/udma133 solution....onboard sound and lan would be fine too.
Then i would buy two extra promise pci ide controller cards.
I would use the normal ide controller for a big hd and a dvd-rom drive.
On every channel of the promise controller and onboard raid controller i would use one writer only.
I am not sure if this will work..perhaps you will get some probs with the irq´s or the busmaster signal.
Pedja
1
You mean that I must have some brand new MB at 800Mhz to pass bus problems?Master said:
I am open (today) one IDE duplicator builded on ACARD controller and I didn't see anything special on controller board (only one chip, but I am not sure that is RAID controller chip). Also, as I know whole IDE/ATAPI specification is under ATA66 standard (right?).
Can you can be more precise about hardware (especially controllers) specification?
Nero Multiple recorders
U can use any older version of nero 5.5.x.x to writer more than 2 recorders upto 10 recorders.
my system
Pentium IV 1.7ghz
Mercury Mainboard (Low End)
256MB SD Ram
40gb seagate hdd (5400 rpm)
2 CMD 649 PCI Raid Card
10 sony crx215E1 48x Recorders.
I connected 4 recorders in each ide cards( 8 recorders)
2 recorders in onboard ide(1 is Prim slave, 1 is Sec Master)
1 hdd as Prim Master in onboard ide
Edited by me warez <> Please read the rules we are warez free
The-poacher <<>> Super Moderator
!gps31
U can use any older version of nero 5.5.x.x to writer more than 2 recorders upto 10 recorders.
my system
Pentium IV 1.7ghz
Mercury Mainboard (Low End)
256MB SD Ram
40gb seagate hdd (5400 rpm)
2 CMD 649 PCI Raid Card
10 sony crx215E1 48x Recorders.
I connected 4 recorders in each ide cards( 8 recorders)
2 recorders in onboard ide(1 is Prim slave, 1 is Sec Master)
1 hdd as Prim Master in onboard ide
Edited by me warez <> Please read the rules we are warez free
The-poacher <<>> Super Moderator
!gps31