Failure To Burn

[meldrew]

Hi
I am attempting to back up some of my favourite DVDs useing the Totally FREE & Easy Dvd backup guide, but when burning useing Burnatonce after exactlly 21 min and a few seconds it comes up with the writing finished flag
and an error report.

I have tried several times with different DVDs but still get the same result Could anyone please give me any ideas as to where I could be going wrong.

Useing

Burnatonce 0.99b

Pioneer DVD RW DVR 106D

Media Sony 4.7GB DVD-RW

Burnatonce Report

TOC Type: 1 = CD-ROM
Using libscg version 'rs-0.7+'
Driveropts: 'burnfree'
atapi: -1
Device type : Removable CD-ROM
Version : 0
Response Format: 2
Capabilities :
Vendor_info : 'PIONEER '
Identifikation : 'DVD RW DVR-106D'
Revision : '1.07'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x0014
Profile: 0x001B
Profile: 0x001A
Profile: 0x0014 (current)
Profile: 0x0013 (current)
Profile: 0x0011 (current)
Profile: 0x0010
Profile: 0x000A
Profile: 0x0009
Profile: 0x0008
Using generic SCSI-3/mmc DVD-R(W) driver (mmc_mdvd).
Driver flags : SWABAUDIO BURNFREE
Supported modes: PACKET SAO
Drive buf size : 1605632 = 1568 KB
FIFO size : 45158400 = 44100 KB
Track 01: data 4206 MB
Total size: 4830 MB (478:34.13) = 2153560 sectors
Lout start: 4830 MB (478:36/10) = 2153560 sectors
Current Secsize: 2048
ATIP start of lead in: -150 (00:00/00)
Disk type: unknown dye (reserved id code)
Manuf. index: -1
Manufacturer: unknown (not in table)
Blocks total: 2298496 Blocks current: 2298496 Blocks remaining: 144936
Starting to write CD/DVD at speed 1 in real SAO mode for single session.
Waiting for reader process to fill input buffer ... Turning BURN-Free on
input buffer ready.
trackno=0
BURN-Free is ON.
Turning BURN-Free off
BURN-Free is OFF.
Performing OPC...
Sending CUE sheet...
Starting new track at sector: 0

CDB: 2A 00 00 0C 8C 41 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 03 00 0C 89 91 0E 00 00 00 00 0C 00
Sense Key: 0x3 Medium Error, Segment 0
Sense Code: 0x0C Qual 0x00 (write error) Fru 0x0
Sense flags: Blk 821649 (not valid)
cmd finished after 1.573s timeout 200s
A write error occured.
Please properly read the error message above.

write track data: error after 1684146176 bytes
Writing time: 1264.525s
Average write speed 22.8x.
Min drive buffer fill was 89%
Fixating...
Fixating time: 0.017s
fifo had 27215 puts and 26528 gets.
fifo was 0 times empty and 13235 times full, min fill was 98%.

 

[PC-GUY]

Do you know you don't need to use Burnatonce 0.99b any more?
I say this cause you could use just DVD Decrypter and DVD Shrink.
For DVD 9 all you have do different is in shrink save it as a ISO and then burn it with DVD Decrypter.
I think from that log file your burner doesn't like your media do you know who makes it? For all you know if you tried different name media it still could be the same manufacture.
You can use DVD Decrypter and put a blank in your burner and it will tell about the media. Just have DVD Decrypter in Mode =>ISO => Write and just copy any past what you see in the right hand box.

 

[meldrew]

Do you know you don't need to use Burnatonce 0.99b any more?
I say this cause you could use just DVD Decrypter and DVD Shrink.
For DVD 9 all you have do different is in shrink save it as a ISO and then burn it with DVD Decrypter.
I think from that log file your burner doesn't like your media do you know who makes it? For all you know if you tried different name media it still could be the same manufacture.
You can use DVD Decrypter and put a blank in your burner and it will tell about the media. Just have DVD Decrypter in Mode =>ISO => Write and just copy any past what you see in the right hand box.

Thanks for the ideas I was just following the script, I didnt want to use DVD-R to start with (not wanting any coasters) and the DVD-RW were the only ones I had, so I will give your suggestion a try.

 

[scarecrow]

DVD Decrypter and DVD Shrink need Nero engine being present to burn, else they don't do a thing.
Seeing your log it's obvious that you don't use pro-DVD in combo with Burnatonce. With the old BAO versions (like the one you use) you will be able to burn DVD's only on a few Pioneer drives and -R media only. For full functionality you need the latest BAO version, and a pro-DVD binary with a licence (licence is free and the way to get it has been described many times here).

 

[VILLA21]

DVD Decrypter and DVD Shrink need Nero engine being present to burn, else they don't do a thing.

DVDDecrypter does"t require Nero engine to write in WRITE ISO mode...